2B Solar Wireless Perimeter Alarm & Auto-Dialler System

This Long Range Solar Powered Wireless Perimeter Alarm is supplied with of a set of 2B-100 Wireless Perimeter Beams, a versatile 4- Channel Indoor Receiver & a Land Line Auto-Dialler.

The beams have a 100 metre detection range & 900 metres transmission range back to the Receiver, the Auto-Dialler will contact up to 9 key-holders by Telephone (with your own pre-recorded message) should the system be Activated.

Receiver:

The Indoor 4 - Channel Wireless Receiver is powered by a standard 3-pin Plug in Transformer and has the following features:

• 4 x Adjustable Dry Relay N/O or N/C Outputs (often used to trigger auto-diallers, timer relays).
• Adjustable 12v DC Outputs (often used with sirens & flashing lights).
• ON/OFF Switch.
• Volume Control.
• Will work with up to 128 sets of Detectors.
• Optional Reminder Bleeps.
• Exit Delay Option.

Receiver:

• 1 x 4-Channel Indoor Receiver.
• 1 x Plug in Transformer. 
• 1 x Rear Mouning Bracket.
• 1 x Manual. 

Detection Beams:

• 1 x Set of 2B Solar Powered Detecting Beams.
• 1 x Set of Wall Mounting Brackets. 
• 1 x Set of Pole Mounting Brackets.
• 1 x Set of Instructions. 

Auto-Dialler:

• 1 x Auto-Dialer.
• 1 x Back up Battery.
• 1 x Power Transformer (12v DC).
• 1 x Telephone Cable.
• 1 x Manual. 

Receiver:

• Receiver Size: 160 (W) x 105 (H) x 35 (D) mm.
• Power Supply: 15v DC 1 amp (plug in transformer).
• ON/OFF Button: Yes.
• Adjustable Volume Control: Yes.
• Available Channels: 4.
• Max sets of Beams per Channel: 32.
• Maximum sets of Detectors per Receiver: 128.
• Output Voltage: 12v DC.
• Output Voltage Duration: 1, 10, 60 second & 5 minutes.
• Built in Chimes: Yes (one per channel).
• Reminder Bleep: Yes (if programmed).
• Exit Delay: Yes 5 minutes (if programmed).
• Frequency: 434.6 MHz.
• Standby Current: 20 mA.
• Alarm Current: 180 mA.
• Relay Rating: 24v DC or 120v AC (2 amp).
• Relay Output Type: Momentary N/O or N/C.
• Wireless Working Range: 900 metres (line of sight).

Detection Beams:

• Beam Size: 590 (H) x 123 (W) x 45 (D) mm.
• Power Supply: Re-chargeable AA Batteries.
• Charging Method: Built in Solar Panels.
• Mounting Methods: Wall or Pole.
• Detection Range: 100 metres.
• Transmission Range: 900 metres (line of sight).
• Frequency: 433 Mhz.
• IP Rating: IP66.
• Distance Between Detection Beams: 60mm.
• Quantity of Built in Detection Beams: 2 sets.
• Charging Port: 9 - 12v DC (500 m/A to 1 amp).
• Built in Buzzer: Yes (turn on with 1 - 6 presses of button, off 7 or 8 times).
• Buzzer OFF (7 with immediate reset, 8 with 3 minutes battery saving reset).

Easy Programming Method:

1. Turn On Beams (switch on rear).
2. Mount the Beams.
3. Line up By Eye, String Line etc.
4. Put the relevant Receiver into Learn Mode.
5. Walk through the Beams, at this time (providing you have them correctly lined up), a low red glow will illuminate briefly.
6. The Signal sent to the Receiver from this set of beams will be learned into the relevant receiver.
7. Take the Receiver out of learn mode.
8. The system is now ready.

Auto-Dialler:

1. You can pre-record two 10 second personal message.
2. You can program between 1 - 9 telephone numbers into it (up to 32 digits)..
3. Dual trigger options.
4. Two message options (trigger 1 & 2).
5. Built in audible alarm or silent activation (adjustable).
6. Siren Duration Adjustable (1 - 99 minutes).
7. Very versatile telephone software allowing all telephone lines to be used easily. 
8. You can program delay trigger from 0 - 60 seconds.
9. You can program delay exit from 0 - 90 seconds.
10. The system can be used with all types of alarm control panels.
11. You can stop the system sending the voice message to other programmed telephone numbers by pressing * or # on the receiving telephone.
12. Battery back up.
13. Plug in Transformer Power Supply (supplied).