4 x 3B Solar Wireless Perimeter Beams with H/D KP GSM Auto-Dialler

Four sets of 3B Solar Wireless Perimeter Security Beams supplied with a 4-channel Receiver & KP H/D GSM Auto-Dialler, ideal for protecting your Perimeter, the 3B Beams have an impressive 100 metre detection range & a 900 metres transmission range back to the Wireless Receiver, the GSM Dialler will contact key-holders by Telephone.


More details

1 525,95 € inc VAT

Four sets of 3B Solar Wireless Perimeter Security Beams supplied with a 4-channel Receiver & KP H/D GSM Auto-Dialler, ideal for protecting your Perimeter, the 3B Beams have an impressive 100 metre detection range & a 900 metres transmission range back to the Wireless Receiver.

The versatile GSM Auto-Dialler will contact key-holders by Telephone & SMS.

It works by installing the four sets of 3B Beams into the locations needing to be monitored (the beams can be up to 100 metres away from each other), plug the Indoor Receiver into a standard type wall socket (up to 900 metres away), connected to the indoor receiver is the KP GSM Telephone Auto-Dialler which has a sim card inserted. When a vehicle or person passes through the beams the receiver will chime and activate the gsm auto-dialer (and any other accessories connected), the gsm auto-dialer will then contact up to 3 key-holders by text message & 5 by telephone. 

Please Note: A sim card is required for the gsm dialer, customers can use both 'pay as you go' or 'contract' type, we recommend a network is chosen which has a good signal at the proposed location of the alarm.

GSM Auto-Dialler:

The KP Heavy Duty Auto-Dialler is constructed with a steel case, ideal for many commercial applications or the harsher environments.

It is connected to the Wireless Receiver by a short length of bell cable (supplied) and communicates through mobile phone networks, a standard sized SIM Card needs to be fitted (you can use either PAYG or Contract).

It is very easy to program by using the built in keypad, and easy to use with the following features:

  • Will send up to 3 text messages when triggered.
  • Up to 5 telephone numbers can be programmed (a maximum of 32 digits).
  • Will contact main key-holder in the event of a 30 minute power failure (optional).
  • Remote  operation (by text message).
  • 4 methods of arming & disarming:
    • Keypad.
    • Remote Control.
    • Auto-setting.
    • Text Message.
  • Adjustable entry & exit delay.
  • Back up battery.
  • 16 wired zones.
  • 16 wireless zones (allows you to fit Intruder & Safety Sensors including wireless door contacts, internal PIR's, smoke & water sensors).
  • 12v output (for connecting to sirens etc).
  • Communication Method: Sim Card.
  • External Aerial can be Fitted (for a better mobile phone signal).

The secret to using a GSM Auto-Dialler with a Perimeter Alarm is to use the Dialler as the central hub of the system, therefore any additional Sirens, Flashing Lights or Relays would be connected to the output of the Dialler (not the internal receiver), this gives you full control, even from remote locations via your mobile.

The Receiver is used for just two reasons, first to receiver the signal from all of the Detectors, the second as a useful Chime unit for when you are at home and you do not need the system Armed.



  • 4 x Dry Relay Outputs (adjustable channels).
  • 12v DC Outputs (adjustable channels & time duration).
  • ON/OFF Switch & Volume Control.
  • Will work with up to 128 sets of Detectors.
  • Optional Reminder Bleeps.
  • Exit Delay Option.
  • 900 metre Wireless Working Range.


Solar Powered Wireless Detector Beams:

These impressive Solar Powered 3B Wireless Perimeter Beams are packed with impressive features listed below: 
  • Battery Powered with Built in Solar Charging: (making for easy installation).
  • 3 x Detection Beam Sets.
  • Dual Detection Technology: (prevents false alarms from small animals and moving debris).
  • 100 metre Detection: (covers more are with less detectors).
  • Impressive 900 metre Wireless Range: 
  • Quality Build.
  • Supplied with Wall & Pole Mounting Brackets.
  • Test Lights: (for easy installation).
  • Top up charging Ports.

The Dual Detection Technology works by having a pair of Detectors (set 60 mm apart from each other) on each Beam, both Detectors have to be breached simultaneously to create an activation (allowing small animals, insects, leaves & debris to safely pass by). There are a pair of detectors on each size of Beam, so the 3B-100 have three pairs whilst the 2B-100 would have two and the 1B would have one. Each pair of detectors work independently of each other resulting in the 3B-100 Beams having three chances to detect an Intruder, and creating a larger invisible perimeter.    

They also have an additional Charging Port which can be used to give the Beams a boost charge should you experience a lengthy duration of low sun light, or perhaps one of the beams needs to be fitted into a slightly covered location. 

They are very easy to install as they have a built in Red Glow Light (for easy lining up).

Additional Accessories:  

You can add additional accessories to this Security System to suit your exact requirements, these include:

  • Wireless Beams (3 sizes).
  • Window Beams (2 sizes).
  • PIR's (2 types).
  • Door Contact.
  • Smoke Detector.
  • Receivers.
  • Wireless Boosters (repeaters).
  • Sirens (wired and wireless). 
If in doubt, please contact us for Advice !!


Available by mail order throughout Ireland, or collection from Dublin.




  • 4 x Set of 3B Wireless Perimeter Beams.
  • 1 x Wireless Receiver & 2 or 3-pin Plug in Transformer. 
  • 1 x Set of Brackets & Screws.
  • 1 x KP Heavy Duty GSM Auto-Dialler, Plug in 2 or 3-pin Transformer.
  • 1 x Set of Manuals.

Wireless Receiver Specification:

  • Size: 160 (W) x 105 (H) x 35 (D) mm.
  • Power Input: 12 - 15v DC 1 amp.
  • Power Supply: 3-pin Plug in Transformer (2-pin available upon request).
  • ON/OFF Button: Yes.
  • Adjustable Volume Control: Yes.
  • Channels: 4.
  • Max sets of Beams per Channel: 32.
  • Output Voltage: 12 - 12v DC.
  • Output Voltage Duration: 2 seconds to 10 minutes.
  • Built in Chimes: Yes (one per channel).
  • Reminder Bleep: Yes (if programmed).
  • Exit Delay: Yes 5 minutes (if programmed).
  • Frequency: 434.6 MHz.
  • Standby Current: 20 mA.
  • Alarm Current: 180 mA.
  • Relay Rating: 24v DC or 120v AC (2 amp).
  • Relay Output Type: Momentary N/O or N/C.

GSM Dialler Specification:

  • Case Construction: Steel.
  • 2 x Aerials: (detachable and extendable).
  • Text Message: (will send up to 3 text messages when triggered, one text message following a power failure).
  • Telephone Calls: (will call up to 5 telephone numbers).
  • 16 x Wireless Zones (fully adjustable).
  • 16 x Wired Zones (fully adjustable).
  • Adjustable Power Failure Time Duration: (instantly or 30 minutes).
  • 12v DC Input: (suitable for solar & battery applications).
  • Can be Armed & Disarmed by: Built in Keypad, Remote Control, Self Auto-Timer & Text Message.
  • Self Monitoring Mode: (optional use).
  • 4 Minute Output Relay: (relay when the alarm is triggered, can operate sirens, lights, telephone dialers).
  • 12v DC Output: (when triggered).
  • Large selection of Alarm Accessories Available.
  • Switch 4 Minute Relay: (can be used for the key-holder to switch on lights etc).
  • Lockable Control Panel.
  • Tamper Switch.
  • Sirens: (can activate external wired & wireless sirens).
  • Size: 225 (w) x 160 (h) x 50 (d) mm.
  • Frequency: 433 Mhz.
  • Quad Band: 850/900/1800/1900 MHz.

Perimeter Beams:

  • Beam Size: 840 (H) x 123 (W) x 45 (D) mm.
  • Power Supply: Re-chargeable AA Batteries.
  • Charging Method: Built in Solar Panels.
  • Mounting Methods: Wall or Pole.
  • Detection Range: 100 metres.
  • Transmission Range: 900 metres (line of sight).
  • Frequency: 433 Mhz.
  • IP Rating: IP66.
  • Distance Between Detection Beams: 60mm.
  • Number of Beams: 1 set.
  • Charging Port: 9 - 12v DC (500 m/A to 1 amp).

Easy Programming Method:

  1. Turn On Beams (switch on rear).
  2. Mount the Beams.
  3. Line up By Eye, String Line etc.
  4. Put the relevant Receiver into Learn Mode.
  5. Walk through the Beams, at this time (providing you have them correctly lined up), a low red glow will illuminate briefly.
  6. The Signal sent to the Receiver from this set of beams will be learned into the relevant receiver.
  7. Take the Receiver out of learn mode.
  8. The system is now ready.

Similar Products

People also bought...

Quick Search

My shopping cart

No products

Shipping 0,00 €
Total 0,00 €

Check out

My account

(Forgot password?)


To receive our news and special offers, please enter your email: